TapeTech Flat Boxes

Click Here For Tape Tech Flat Box Parts Diagram & Price List

The flat box applies joint compound over taped joints. It comes in three widths, generally used for finishing as follows:

7": applies bed coat
10": applies finish coat
12": applies skim coat

This tool requires little effort to operate and is designed to produce uniform results every time.

The flat box is controlled by a specially designed handle. These handles come in multiple lengths from 34" to 72" The handle is attached to the box by sliding the box onto the handle and tightening the two wing nuts.

Load the flat box through the opening behind the blade using the box adapter with the slot adapter inserted.

To apply compound, draw the flat box steadily along the joint while applying pressure with the handle. This dispenses compound through the opening at a steady rate. The tool is always run with the wheels leading and the blade trailing. The handle should lead the box, except at the end of joints.

The adjustable metal blade trowels the compound with the precise crown needed. This is set using the crown adjustment wheel. This dial controls the amount of crown left by the box with 1 being the most and 5 the least.

Before starting to run any joint, lock the box handle at a slight angle by squeezing the handle grip with one hand. Your other hand should grip the handle near the Flat Box.

Place the flat box at the end of the joint and apply pressure with the handle to start the compound flowing. Release the hand grip to unlock the handle and allow it to find its own natural position. Draw the tool along the joint, leading with the handle and applying pressure to distribute the joint compound onto the wallboard surface.

Near the middle of the joint, lock the handle and by gradually decreasing pressure, remove the flat box from the wallboard surface with a sweeping motion.

Reverse hand positions and begin again at the other end of the joint. Again draw the Flat Box along until you reach the previous stopping point. Lock the handle and remove the flat box from the surface with a sweeping motion.

This procedure is followed for all ceiling joints and horizontal wall joints.

To cover vertical wall joints, lock the handle and begin covering the joint from the bottom up to a height of about 30" Sweep off and begin again at the top of the joint.

Draw down the joint until you reach the previous stopping point. Then lock the handle and sweep off the surface, neatly joining the two finished sections.

For door or window openings, always work from the corner, moving toward the opening. Just before the wheels reach the opening, lock the handle and lift the wheels to keep them from dropping into the opening, then sweep away from the wall.

Before starting the finish coat, lightly sand the dried topping coat to remove any small crumbs. Fill the 1 on or 12" Flat Box and set the dial to #3 for a medium crown. Apply a finish coat to all joints. After the two side by side coats have dried, finish them with a 10" or 12" skim coat over the center of the joint.

Reset the crown to #5 for a tight crown then cover the flat joints on the ceilings and walls.

Maintenance

Clean thoroughly with a brush and water (or a water hose) to remove all joint compound from the tool. Then, after the tool is clean, lightly oil with Ames® Bazooka® Oil or any light machine oil.

Box Blade Replacement

1. To remove the used blade, place the tip of a screwdriver against one end of the blade and tap the screwdriver with the palm of your hand.

2. If the blade does not pop out, tighten the screw at one end of the brass blade holder, forcing the end of the blade out. Back the screw up and again tap the end of the blade.

3. Use one end of the used blade to clean any dried compound from the blade holder slot.

4. Remove both right and left skid covers, but leave the skid clips in place.

5. Slightly bend the new blade approximately 2 inches from both ends. This will help secure the blade while the tool is in use.

6. Start at one end, pressing the blade all the way into the blade holder, working to the other end.

7. Install new skid covers. The "dog ear" on the covers should press against the back side of the new blade and be flush with the blade holder (about the thickness of a thumbnail lower than the blade edge).

Send email to webmaster@fantastictools.com with questions or comments about this website

Copyright 1999 - 2006 Fantastic Drywall Tools and Supplies

Last Modified: Tuesday October 09, 2007